World Encyclopedia of Cars
The best old cars, news and reviews about old cars. Stay in touch!

Warynski K-606

All Warynski Photos

Warynski K-606 - information: Warynski K-606 is a very good car, that was released by "Warynski" company. We collected the best 11 photos of Warynski K-606 on this page.

Brand Name Warynski
Model Warynski K-606
Number of views 78520 views
Model's Rate 8.9 out of 10
Number of images 11 images
Interesting News
  • Audi’s electrified future.

    The introduction of mild hybrids to Audi’s model range is set to edge efficiency ever closer to the kind of economy figures enjoyed by TDI owners. But it doesn’t mean the death of the diesel engine, as the introduction of cutting edge technology can be paired to both TDI diesel and TFSI petrol engines. Audi says that within ten years, its entire model range will feature the technology. The key elements of the new system are an 11 Ah capacity lithium-ion battery pack and belt starter generator, with the latter replacing the current starter motor. Coasting becomes possible from around 9mph upwards, so that if the driver takes their foot off the accelerator, the car will coast along for a short time with the engine off, saving fuel. It’s possible to recuperate up to 5kW (7bhp), with the generator returning that power, reducing fuel usage and boosting economy as a result. And while this system can be integrated into current 12-volt systems, Audi is on the verge of announcing that it will put a new 48-volt system into production, with a capacity of harnessing 12kW (16bhp), that will allow coasting for up to 30 seconds, delivering even better efficiency compared to the 12-volt system. The company first gave a glimpse at the technology in the Prologue Concept car last year at the Los Angeles motor show. Other benefits of the introduction of a 48-volt electrical system includes the ability to have much smaller cable cross sections, reducing the weight of the wiring harness, and because it has four times the power, there’s opportunities to add additional innovative technology for the suspension and drivetrain. Further into the future, Audi’s engineers plan to convert the auxiliary systems, like pumps, superchargers for the engine, transmission and air conditioning system to 48 volts. Today these are driven hydraulically or by the engine, but in the future they will be powered by electricity and lighter and more compact. Audi will soon announce an electromechanical active roll stabilisation system, which features an electric motor and a three-stage planetary gearbox that separates the two halves of the stabiliser from each other. For relaxed and comfortable driving, the two halves are decoupled, resulting in cossetting ride comfort. For the sportier driver, the tubes are interconnected and twist against each other, delivering a tauter, more dynamic ride, and less roll when cornering. The front and rear stabilisers can also be adjusted independently allowing even greater degrees of fine tuning. The system is also capable of harnessing energy, and the motor can act as a generator, converting it to electrical energy. But Audi’s engineers are already looking at a second, more advanced project using the 48-volt setup, though it is still in the very early prototype stage. Being developed under the working title of eROT, an electromechanical rotary damper replaces today’s hydraulic item. The system isn’t too far apart from the active roll stabilisation arrangement in terms of basic principles, but a strong lever arm absorbs all of the forces that occur on a bumpy road, and via a series of gears, the force is transmitted into an electric motor, which then converts it to electricity. Recuperation is, on average, around 150 watts on an average road, with a freshly resurfaced road generating as little as 3 watts, while a badly maintained country lane may generate as much as 613 watts. Over a cross section of different roads, CO2 emissions savings could be as much as 3g/ km or four to five mpg.
  • 2017 SUZUKI GSX-R1000 CONCEPT.

    Racers and sportbike riders have been waiting impatiently for several years now for an updated Suzuki literbike, but the end is in sight: At the EICMA show last November, the company finally unveiled a new GSX-R1000. But while the new bike was labeled as a 2017 model, it was also called a “concept,” indicating there may still be work to be completed before it reaches production. Suzuki says that the goal for the new bike was to create the “most powerful, hardest-accelerating, cleanest-running GSX-R ever built,” and the “lightest, most aerodynamic, and best-handling GSX-R1000 ever.” To that end, the bike benefits from lessons learned from the GSX-RR MotoGP project. Specifically, the GSX-R uses what Suzuki refers to as a “Broad Power System,” intended to maximize top-end power without sacrificing low-end and midrange torque via four new features: variable valve timing, valves operated by finger followers, top-feed fuel injectors, and dual SET valves in the exhaust headers. Suzuki’s Variable Valve Timing System utilizes a ball-and-groove arrangement on the intake camshaft, activated by centrifugal force stacking the balls in different grooves. As rpm increases, the intake cam is retarded, optimizing cam timing over the rpm range. The new valve train also uses a finger follower setup to improve valve control and reduce moving mass in the top end, allowing increased valve lift and higher peak rpm. The top-feed fuel injectors are located in the airbox (they were previously mounted in the throttle bodies) to better atomize the fuel for more top-end power, again without sacrificing low-rpm output. And the final part of the Broad Power System is Suzuki Exhaust Tuning-Alpha, which utilizes a butterfl y valve between the number one and four exhaust headers and another between the number two and three headers. The valves remain closed at lower rpm to enhance torque and open at higher rpm for more power. Another goal for the engine was to “optimize dimensions to enhance cornering performance” as well as make the chassis as compact as possible. The frame is all new and has revised geometry, though again no numbers were given. Suspension consists of a Showa Balance Free Fork and Balance Free Rear Cushion shock very similar to those used on the 2016 Kawasaki ZX-10R; the fork has external nitrogen-charged oil reservoirs and external damping circuits, and the shock is Showa’s latest iteration of the BFRC and is significantly lighter. Other chassis updates include high-volume intake ducts, a lower top and sleeker design for the fuel tank, and more aerodynamic bodywork. Even the fairing mounting bolts have been redesigned, with a new fl at-top shape to reduce air resistance, with other mounting hardware recessed to prevent turbulence. No mention was made of the new GSX-R’s brakes aside from the use of electronic ABS, but the calipers are very similar to the previous model’s Brembo four-pot monoblock units. The rotors, however, appear to be a variant of Brembo’s T-drive discs, with half the traditional buttons replaced by T-shaped pins. According to Brembo, the assembly system transfers braking force more effectively, is lighter, and has greater resistance to thermo-mechanical stress. A single-valve ride-by-wire throttle assembly replaces the old model’s dual-valve setup, and the electronics package now features a 10-level traction control system, three power modes, a quickshifter that works on upshifts as well as downshifts, and launch control. The press material contains no mention of an IMU as part of the electronics package; in this regard the GSX-R may be a step behind the YZF-R1 and new ZX-10R, but this is one aspect that could very well change before the bike reaches production. No word was given on price or availability for the new model, but with race teams the world over clamoring for the updated platform, it’s a safe bet the new bike will be a very-early-release 2017 model.
  • This is Yamaha S10000R.

    YAMAHA ALWAYS SAID there would be larger MTmodels, and that the crossplane-crank inline-four engine fromthe YZF-R1 could be used. Given theMT-07’s twin andMT-09’s triple are ‘crossplane concept’ and called the CP2 andCP3, it would kindamake sense to have an actual crossplanemotor in the range. So here’s the newMT-10. This isn’t just the engine froman R1. Unlike its purposebuilt siblings, and despite promising to be ‘enjoyed on any road, any time and at any speed’, theMT-10 is heavily based on themachine that donates its gravelly, snarling engine. Frame, forks, shock and brakes are nicked fromthe sportsbike (or, to be precise, the slightly lower-spec R1-S that they get in the USA). This is Yamaha’s S1000R. Obviously there are changes. The 998cc engine has different pistons, crank, intake, exhaust and injection for bottom-end balls and midrange might, and revised gearing. Like other MTs there are three ridingmodes, but the MT-10 also has cruise control and threelevel traction. A quickshifter will be optional. The frame has ‘optimised strength/rigidity balance’, with a steel subframe andmodified settings for the suspension, and a stubby 1400mmwheelbase - just 20mm longer than the trim newMT-03. Radial calipers have ABS, and the Bridgestone tyres are specially developed for the bike. You’ll get 17 litres in the tank and there’s a 12v power socket. Colours? Blue, black, or the ‘Night Fluro’ grey with high-vis wheels that’s available across theMT range. Yamaha have trodden this path before. The now-defunct FZ1was based on an R1, but its attitude and revvy delivery made it hard work against rival nakeds of the day. Times change however, and now we’re in the age of the supernaked theMT could be just the job. Yamaha haven’t decided howmuch power or weight to claim, or howmuch it’ll cost. But they do assure us that the new MT-10 will be here in May.
Top Warynski models
Popular Searches
World Encyclopedia of Cars
Copyright 2015. All rights under protection.